What did you do at your reloading bench today?

[MyretireChlo&Miss]

Well we just got 10 inches of snow here in nothern Wisconsin, Happy Easter. So before the ham, I made a media seperater out of a 5 gallon bucket and a smaller bucket that spins on a pipe that goes through the smaller container that I drilled full of holes. Works great. Happy Easter to all.

[fortyshooter]

Well my long awaited MB 158 gr. bullets should be delivered today so will be loading up some .38 Specials soon!

[Shakey Jake]

I loaded up some .38+P loads, 158 gr Nosler, for the S&W 14. Also loaded up some .44 mag loads using Nosler 200 gr. I've not loaded them before and made up about 20 of them to test out.
Jake

[RanchRoper]

I only got 50 rounds of 200 gr done this weekend, but I did spend a lot of time horseback...

[JEBar]

ordered a 45 caliber RCBS bullet puller collet from Midway .... I was somewhat surprised to find neither Bass or Cabela's off it .... cheaper from Midway paying shipping than from Amazon on Prime

[Shakey Jake]

ordered a 45 caliber RCBS bullet puller collet from Midway .... I was somewhat surprised to find neither Bass or Cabela's off it .... cheaper from Midway paying shipping than from Amazon on Prime

I find a lot of reloading stuff cheaper on eBay and usually with free shipping. I check out Midway, Midsouth, Amazon, and eBay before ordering and then pick the least expensive with shipping. I just ordered a L.E. Wilson Cartridge Max Gage in .44 mag from ebay with free ship cheaper than the others.
Jake

[JEBar]

I've never spent much time on eBay

[Vaquero]

I've bought quite a bit from ebay over the years.

Just struck a deal with a member of another gun forum for 200 pcs of 45 colt once fired and cleaned brass for $30 shipped.

RP

[fortyshooter]

Got a bunch of .38 Special brass running in the tumbler and more waiting for primers.

[JEBar]

received notice from Amazon that our Hitch Tightener (we ordered back on March 31st) needed to stabilize our portable loading station should arrive next Tuesday .... once it arrives we plan to put the station to work

[BigAl52]

I bought more magazines for my Ruger PC Carbine and ordered 1000 165gr HP Xtreme 40 S&W bullets.

[Rifletom]

I've bought quite a bit from ebay over the years.

Just struck a deal with a member of another gun forum for 200 pcs of 45 colt once fired and cleaned brass for $30 shipped.

RP

Dang Randy! That is a heck of a deal. You done good fella. Load them up!

[RanchRoper]

I've bought quite a bit from ebay over the years.

Just struck a deal with a member of another gun forum for 200 pcs of 45 colt once fired and cleaned brass for $30 shipped.

RP

Nuts, I missed 200 pieces...

[leverjc]

Rolled up some .357's toady for my BB. It seems to prefer Fiochi 158grn's rated at 1250fps to the 125grn hand loads I had already loaded for my Security Six. The 125's are max w296 and shoot well out of the revolver and not bad out of the Henry but the Fiochi groups have me spoiled. I have worked up some Nosler !58grn with w296 and CFE pistol. I hope my guns like the Noslers because I bought a bunch of them on sale. does anyone have any experience with the Nosler pills.

[JEBar]

we've used Nosler 158 gr 357 JHP's as our deer hunting bullets for over 30 years .... during that time they have never failed us and have consistently performed flawlessly .... for practice bullets we use Zero 158 gr JHP ===> http://www.rozedist.com/mm5/merchant.mv ... de=ZBJ-38S .... they are much cheaper and perform well

[leverjc]

JEbar, Thanks for the feed back on the Noslers. I loaded them 15.5, 16 and 16.5 grns of 296 and hoping for the best.

[JEBar]

I loaded them 15.5, 16 and 16.5 grns of 296

that should most certainly move them on down the range .... Per Nosler's manual we load their max recommended charge of 14.8 grns of 296 .... looking forward to following your load development

[fortyshooter]

Finished loading 150 rounds of 158 gr. 38 Specials and started on .357 Magnum 180 gr. Pugs again.

[Rifletom]

Finished off all my .45 Colt brass I have, now, on to some coated 158gr rnfp Missouri bullets. Haven't had the chance to pick up my 180's yet from local shop, but, he has them and said not to worry. So, 12.5-13.0 gr 2400 it is. Works pretty good in the Henry.

[Grunt67]

Started working on a batch of 100, 9mm . Hornady XTP 124 gr., CFE pistol, 5.2 grs., CCI primer.
Wanted to go to the woods shooting the Henry, but waay to windy to be in the woods. Tree or limb blow down on my noggin or truck,
would just about ruin my day, LOL