Henry Rifle Forums

Ok, so the latest offering in my horse trading life is one of either a JM Marlin in .444 or a late Remlin 1895 CB in .45-70 Gov. Now I know the wisdom is to always go JM, but I don’t reload, and don’t intend to start again for a very long time. .444 is pretty thin on the ground at the best of times, and I want any gun I buy to be able to carry out it’s appointed duties. I also hate oddball calibres (.35 Rem is another one I don’t care for) as I want to be able to find factory ammo locally.

With that said, both these rifles are near new, with very little use, and I can trade my mostly unused Ruger American in 7-08 for either one. I really can’t go wrong from a financial standpoint, but given the No reload scenario, is there really any reason I should consider the .444? It’s not worth significantly more than the 1895 CB, and I FAR prefer the Texan stock and Octogon barrel of the CB. The one thing with the CB is, I would not leave it as a 26” barrel. I would have my smith take it down to 18 or 20”. I wouldn’t do this to a JM, but Remlins are “expendable” in my eyes. There was a shorter JM Cowboy model in the past, so I don’t think it’s a terrible idea. I’d basically be making a big bore Texan carbine. I’m not sure how this would effect value, but also not sure I’d give a damn

Thoughts? Am I missing something significant here?

Photos of the 26” version, and an older JM with what I’m guessing is a 20” barrel?

Seller of the shorter barrel on I stole picture of says it’s 18.5” and apparently only 1000 or so were made in the shorter barrel.

Well Red, you do know what they say about opinions right?
Can't believe you dis'd the mighty 35 Rem chambering like that. One of my favorites.

Now as to the Big bores, I'm a Big fan of the t-4's and own a pair.
Have never understood the awe of the ole 45-70, but to each his own.
The biggest jam-0-matic I've ever witnessed was a JM 45-70 that belonged to the f-i-l.
Finally got it operating fairly well and we sent it packin. Never wanted another.
After reading this thread before I started this post I went to Ammoseek.
The price of each are nearly the same, but I do know that on a regular basis that 45-70 is generally easy to find.

As to chopping the barrel of the Remlin I wouldn't think twice about it if that is what you want.
To me that 26" octagon is a thang of beauty.
Heck, back in the spring of '16 I picked up a like new 1975 RC 35 Rem for $300 + some changes.
The next year I had it chopped to 16.5" and love it. It did devalue it considerably, but
guess what? I couldn't care less. That thing is a dream to carry in and out of the woods.
Shoots every bit as good as before and drops whitetails with ease.
And I don't plan for it to leave before I do.

Well, guess I weren't much help, but there ya go.
One opinion, for what it's worth.

RP

Cut the barrel on the Remlin. I have shortened a couple of guns myself, they proved to be difficult to resell, and I lost a lot of money. Use a good smith, make sure he refinishes the cut portions to match, and keep the receipt. I personally would cut it to less than 17”. The .45/70 does fine from that length and it makes for a very handy carbine. This was my 2004 1895 STP (limited edition of 200), with factory 16.25” barrel.

FYI any rifle less than 20” with a cut down barrel is illegal to possess in Canada, but a factory made one is fine. Go figure….. this info was from ten years ago.

My Marlin had severe restrictions underneath the two sight dovetail slots, and it definitely required fire lapping, after that it shot fantastically.

John Davies
Spokane WA

Just get both of them then you dont need to decide. 444 would be my choice. Ive owned both and I like the 444 it will do anything you need to do.

John E Davies wrote: ↑

Mon Jan 22, 2024 9:44 am

Cut the barrel on the Remlin. I have shortened a couple of guns myself, they proved to be difficult to resell.

FYI any rifle less than 20” with a cut down barrel is illegal to possess in Canada, but a factory made one is fine. Go figure….. this info was from ten years ago.

I was aware that there was a law, but couldn’t remember the length. My smith will know. It’s ironic that there is a law about shortening, but it’s fine to own a factory SBR. I have a 870 clone with a 12” barrel. No problem. Add a full stock to a mares leg, have at it! You should be able to cut to any length that factory offers, as long as the factory version is legal. Cabelas had an exclusive 18.5” version from the factory, so that length should be legal, not to mention the current and past 16” trappers that are fine. Too bad gun laws are made by people with next to zero gun knowledge or common sense…

I’m going to look for .444 ammo before I make a decision, as the vast majority of people polled both here and on Marlin Owners are suggesting that I go with that one. Not surprising considering the hatred of Remlins over there. I am one of the few over there that actually owns a late Remlin, and know that the later ones are in fact, well finished and great shooters.

My smith (who is a friend and in my circle of hunting friends) is also the oldest son of the person with likely the biggest collection of leverguns in western Canada, so I will ask his opinion on which way to go.

And on legal barrel cut length, is the chamber considered part of the barrel? I think it is, but don’t know legal definitions. I’m sure that definition changes with jurisdiction too.

Those of you that own .444s, what is the barrel length on them? This one is the standard one, not an XLR or P model, although if it were a P, I’d be much happier.

Red, I've also owned both 45-70 and 444 JM Marlins. never owned a Remlin, but I know several local shooters who bought late edition Remlins and love them. No problems at all. There really shouldn't be, anyway, because the 336/1895 action is pretty fool proof.

I loved the 444 Marlin as a shooting round. Much flatter trajectory than the 45-70, for instance. Unfortunately, if you're shooting factory ammo, only, finding 444 factory ammo is going to take more tine and money than it's worth if you plan to do any amount of shooting at all. You'll actually spend more time hunting ammo than actually shooting it. The T4 isn't dead, yet, but it's getting there. Real shame, but that's the reality.

By contrast, I can walk into any local store that sells ammo and find 45-70. It's almost all the 300-350 grain hunting loads, because it's a popular cartridge in our area. If I want to find some of the more traditional 405 grain loads or cowboy loads for my Ruger No. 3, I have to order online.

The Marlin 444s that I owned were all the standard 22" barrel versions. Pretty sure the P was an 18.5" ported.

Red the two I have are quite different. The first one is a '87 year model with a 22" micro-groove barrel.
The second one I picked up is the P model, and yes to NCG it is ported and has the ballard rifling.
It is louder then the long barreled one, but is the one I shoot the most.
The '87 SS (sporter safety) not stainless, is scoped and the P wears a peep.

RP